Cleaning And Lubricating Overhead Door Hinges, Rollers, And Tracks

    Need a repair technician?

    Our garage door repair team in Calgary are the best at what they do.

    CALL ☎️ (587) 316-9739

    Or leave a message.

    Cleaning And Lubricating Overhead Door

    The most significant moving component of a house is the garage door, which goes up and down daily.

    Daily usage of manual or electrical garage doors can wear out the rollers and misalign the tracks.

    This leads to the garage door dragging or binding, making it increasingly difficult to lift and lower.

    Like all mechanical units, a garage door needs periodic maintenance to perform optimally daily

    To allow it to operate correctly, efficiently, and smoothly, it is vital to keep it well-maintained.

    This requires cleaning and lubrication of the overhead rollers, tracks, and door hinges.

    Conducting thorough maintenance can prevent garage door owners from spending money, replacing it with a new one, or having unnecessary repairs.

    Here are some essential tips to help garage door owners know what needs to be done for garage door cleaning and lubrication.

    Clear The Vicinity of the Garage and the Door

    Remove any vehicles parked inside and any other equipment or objects that could make it difficult to reach the tracks and rollers before conducting maintenance.

    When inside the garage, close the garage door and set up a step ladder to check the rollers and tracks.

    Make sure that there’s enough light inside to be able to get the job done comfortably.

    To avoid build-up as well as causing more harm than good, do not use water or other chemicals.

    To sweep off any dust and dirt, use a broom instead.

    Clear out insect nests, like spider webs, that may trap in dirt and particles that may obstruct the tracks and wheels.

    Be extra careful and make sure the whole garage door area is properly clean before lubricating.

    Inspect for Worn Out Rollers, Nuts, and Bolts

    Examine all the rollers on the garage door and check if it needs to be maintained only or replaced entirely.

    Contact a garage door technician immediately to repair or replace them if they seem to be worn down.

    Poorly operated rollers can cause premature wearing out of opener components and the garage door to jump the tracks.

    They seem to cause unwanted squeaking and grinding noises as well.

    Thoroughly examine all the bolts and nuts that keep the track mounting brackets and roller hinges in place.

    Tighten any hardware that seems to have loosened over time, and it should be repaired when checking the device if any bolts or nuts have rusted.

    Cleaning the Door Track

    To dislodge any accumulation of grease, grime, or dirt, clean the inside of the tracks with an old toothbrush.

    To clear the cleaner and dirt, spray the disc brake cleaner on the tracks and then wipe them out with a clean rag.

    When the garage door is closed, clean the upper sections of the guide board, and clean the lower sections of the board when the door is open.

    This will prevent the rollers from blocking the access to the track’s channel by cleaning the track in this way.

    Track Alignment

    Test both of the horizontal and vertical tracks for alignment.

    Make sure that they are slanted slightly from the opening towards the back wall of the garage.

    At the very same height from the ceiling, the tracks should also be hung.

    To get the tracks in the correct place, make any changes possible or call for professional help.

    Proper Lubrication of the Garage Door

    Proper lubrication is one thing that might be the most relevant when it comes to the efficient functioning of the garage door.

    When the garage door opens and closes, it helps eliminate the squeaky noise and ensures a smooth and seamless operation.

    A thin coating of silicone spray lubricant can be used on garage rollers, tracks, and door hinges.

    However, this causes other debris to build up and accumulate dirt if too much lubricant is added.

    Lubricate the points at which the hinges are pivoting.

    Make sure, however, the plastic hinges are not lubricated as they will decay with it.

    Apply garage door lubricant to the rollers of the garage door.

    Seek a Garage Door Repair Technician

    If these tips are lacking, it is best to contact a garage door repair company to maintain the electrical or manual garage door.

    Overhead door repairs in Calgary can be found easily.

    Rate this post
    David Martin

    David Martin

    Servicing garage doors for over a decade has thought me a thing or two about garage doors. In this blog I will try to share with you all I've learned over the years. I hope you find these tips helpful for a DIY fix before paying for a technician. If you still need help, don't hesitate to give us a call.

    Contact Us
    COVID-19 NOTICE:
    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar